Roll Stand Assemblies G C X I n s t r u m e n t M o u n t i n g S y s t e m

The LiDCO™plus Hemodynamic Monitor can be mounted to the LiDCO™plus roll stand.

These stands enable seamless integration of advanced patient monitoring anywhere around the patients bedside. The ergonomic design takes up less space and lets you work in different positions. Our LiDCO™plus stand solutions provide you with choice and makes your LiDCO™plus system easy to use and easy to maintain.

Alternatively, the LiDCO™plus Hemodynamic Monitor can be fixed to the wall, bed stand or anaesthetic trolley using standard GCX mounting options.

ROLL STANDS UNITS:

Current Mounting Assembly		Previous Mounting Assembly

Table of Contents:

MOUNTING ASSEMBLY INSTALLATION GUIDE

CASTERS, MAINTENANCE & CLEANING

LiDCO SENSOR INTERFACE

DESKTOP STAND MOUNTING INSTRUCTIONS

WALL MOUNTS AND MORE LiDCO MOUNTING SOLUTIONS

NEW ROLL STAND BASE FOR 2004

MOUNTING ASSEMBLY INSTALLATION GUIDE

MOUNTING ADAPTER FOR THE LIDCO HEMODYNAMIC MONITOR

ITEM DESCRIPTION	QTY
Mounting Adapter	1
M4 x 10mm Pan Head	Machine Screw (PHMS)	8

TOOLS REQUIRED: Philips screwdriver.

ATTACHING THE MOUNTING ADAPTER AND MOUNTING THE MONITOR
1. Place the Monitor face down for access to the four (4) threaded mounting holes on the rear housing (Pic 1).
2. Attach the Mounting Adapter to the Monitor using four (4) M4 x 10mm PHMS (Pic 2).

3. Insert two (2) M4 x 10mm PHMS in the top two (2) threaded holes of the Mounting Adapter (Pic 3). Leave 1/4"(6 mm) of thread exposed to allow the screws to fit into the slots on the VESA Mounting Plate.
4. Guide the two (2) top screws into the mounting slots on the VESA Mounting Plate (Pic 4). Do not fully tighten these mounting screws until Step 6.

5. Insert two (2) M4 x 10mm screws in the lower two (2) mounting holes (Pic 5), securing the Monitor to the VESA Mounting Plate.

6. Tighten the top two (2) mounting screws (Pic 6).

MOUNTING ASSEMBLY INSTALLATION GUIDE

1.0 ASSEMBLING THE ROLL STAND WITH COUNTERWEIGHT AND UTILITY BASKET

PARTS REFERENCE

The following parts and hardware are provided for this procedure:

ITEM DESCRIPTION	QTY
Roll Stand Post, 44'' with 6'' Offset	1
Roll Stand Base	1
Counterweight, 12 lbs	1
5/16-18 x 3-1/2'' Hex Head Cap Screw (HHCS)	1
5/16 Split Lock Washer	1
Roll Stand Washer, 2''	1
Wire Utility Basket, 6''	1
Nylon Basket Clip - Utility Basket Attachment	2
#8-32 x 1-1/2'' Pan Head Machine Screws (PHMS)	2
#8-32 x Hex Nut	2

Tools Required: Philips screwdriver, 1/2'' wrench or nutdriver.

1. Attach the two (2) Nylon Basket Clips to the Wire Utility Basket in accordance with separate installation guide DU-UT-0002 Rev B. Insert the two (2) #8-32 x 1-1/2'' PHMS and #8-32 hex nuts in the Basket Clips but do not tighten them at this time.

2. Slide the Basket onto the bottom end of the Roll Stand Post (Pic 1) and insert the Post in the center of the Roll Stand Base (Pic 2).

3. Lay the Roll Stand on its side for access to the bottom of the Base.

4. Insert the 5/16-18 x 3-1/2'' HHCS through the lockwasher, 2'' roll stand washer, and Counterweight as shown in Pic 3. Using a 1/2'' wrench or nutdriver, secure the Counterweight to the bottom of the Roll Stand Post (Pic 4).

5. Slide the Wire Basket to the desired mounting position on the Post and tighten the two (2) Basket Clip screws to secure the Basket.

2.0 ATTACHING THE ROLL STAND HANDLE

PARTS REFERENCE

The following parts and hardware are provided for this procedure:

ITEM DESCRIPTION	QTY
Roll Stand Handle	1
1/4-20 x 5/8'' Socket Head Cap Screw (SHCS)	2
3/16'' Hex Wrench	1

Tools Required: 3/16'' hex wrench (provided).

1. Remove the Rear Clamping Block from the Handle (see photo above right) by unscrewing the two (2) 1/4-20 x 5/8'' socket head cap screws (SHCS).

2. Position the Handle at the desired height on the Roll Stand Post and attach the Rear Clamping Block to the Handle as shown in Pic 5.

3.0 ATTACHING THE POWER OUTLET STRIP (EURO VERSION)

Installation Note: The Power Outlet Strip is an optional accessory and may not be included with this Roll Stand Kit.

PARTS REFERENCE

The following parts and hardware are provided for this procedure:

ITEM DESCRIPTION	QTY
Power Outlet Strip/Front Clamping Block	1
Rear Clamping Block	1
1/4-20 x 5/8'' SHCS	2
3/16'' Hex Wrench	1

Tools Required: 3/16'' hex wrench (provided).

1. Position the Power Strip/Clamping Block on the Roll Stand Post and attach Rear Block to Front Block (Pic 6) using two (2) 1/4-20 x 5/8'' socket head cap screws (SHCS). Mounted Power Strip shown in Pic 7.

NB: USA customers please use USA power distribution.

4.0 ATTACHING THE SYRINGE/BAG HOLDER

PARTS REFERENCE

The following parts and hardware are provided for this procedure:

ITEM DESCRIPTION	QTY
Clamping Block with Syringe/Bag Holder	1
Clamping Block, Rear Half	1
1/4-20 x 5/8'' Socket Head Cap Screw (SHCS)	2
3/16'' Hex Wrench	1

Tools Required: 3/16'' hex wrench (provided).

1. Position the Syringe/Bag Holder on the Roll Stand Post as shown and attach the Front Block to the Rear Block (Pic 8) using two (2) 1/4-20 x 5/8'' socket head cap screws (SHCS). The Syringe/Bag Holder should be attached to the Post as shown in Pic 9.

5.0 ATTACHING THE SENSOR INTERFACE BRACKET/CORD LOOP HOOK

PARTS REFERENCE

The following parts and hardware are provided for this procedure:

ITEM DESCRIPTION	QTY
Sensor Interface Bracket/Front Clamping Block Assembly	1
Cord Loop Hook/Rear Clamping Block Assembly	1
1/4-20 x 5/8'' Socket Head Cap Screw (SHCS)	2
3/16'' Hex Wrench	1

Tools Required: 3/16'' hex wrench (provided).

1. Position the Clamping Blocks (Bracket and Hook) at the desired height on the Roll Stand Post and attach the Rear Block to the Front Block (Pic 10) using two (2) 1/4-20 x 5/8'' socket head cap screws (SHCS).

2. Mount the Sensor Interface by inserting the four (4) mounting studs into the slots in the mounting bracket and sliding downward into locking position (Pic 11).

6.0 ATTACHING THE PRINTER TRAY AND POWER SUPPLY BRACKET

Installation Note: The Printer Tray/Power Supply Bracket is an optional accessory and may not be included with this Roll Stand Kit.

PARTS REFERENCE

The following parts and hardware are provided for this procedure:

ITEM DESCRIPTION	QTY
Printer Tray/Front Clamping Block Assembly	1
Rear Clamping Block	1
1/4-20 x 5/8'' SHCS	2
Power Supply Cage	1
M3 x 4mm Pan Head Machine Screw	4
3/16'' Hex Wrench	1

Tools Required: Philips screwdriver, 3/16'' hex wrench (provided).

Installation Note: The Printer Tray is attached to the Clamping Block for right-side access to printer controls. The Clamping Block may be unscrewed from the Printer Tray and reattached to the opposite side of the Tray for left-side access to printer controls.

1. Insert the Power Supply in the Power Supply Cage as shown in Pics 12 and 13.

2. Align the four (4) mounting holes in the Power Supply Cage with the four (4) threaded holes in the bottom of the Printer Tray (Pic 14). Attach Cage to Printer Tray using four (4) M3 x 4mm PHMS (Pic 15).

3. Position the Printer Tray/Power Supply Cage near the top of the Roll Stand Post (Tray facing rear side of post) and attach the rear half of the Clamping Block using two (2) 1/4-20 x 5/8'' SHCS (Pic 16). Mount the printer in the Tray as shown in Pic 17.

7.0 ATTACHING THE MANUAL TILT CLAMP/VESA MOUNTING PLATE ASSEMBLY

PARTS REFERENCE

The following parts and hardware are provided for this procedure:

ITEM DESCRIPTION	QTY
Manual Tilt/VESA Mounting Plate Assy.	1
#10-32 x 3/4'' Flat Head Machine Screw (FHMS)	3
Adjustable Lever, Tilt	1
Black Lexan Cover - Cover MT Clamp-Mounting Screws	1
9/64'' Hex Wrench - Tilt Tension Adjustment	1
Mounting Adapter,Advantech Display	1
M4 x 10mm Pan Head Machine Screw	8

Tools Required: Philips screwdriver, 9/64'' hex wrench (provided).

1. Attach the Manual Tilt/VESA Mounting Plate Assembly to the top of the Roll Stand Post using three (3) #10-32 x 9/16'' FHMS (Pic 18).

2. Screw the Tilt Adjustment Lever into the threaded hole (clockwise) on top of the Manual Tilt Clamp (Pics 19 and 20). Note: It may be necessary to tilt the Mounting Plate down to allow insertion the Adjustment Lever.

Note: The Tilt Adjustment Lever is a multi-position clamping lever that operates by lifting, rotating, and releasing the handle.

8.0 ATTACHING THE MONITOR MOUNTING ADAPTER AND MOUNTING THE MONITOR

PARTS REFERENCE

The following parts and hardware are provided for this procedure:

ITEM DESCRIPTION	QTY
Mounting Adapter	1
M4 x 10mm Pan Head Machine Screw (PHMS)	8

Tools Required: Philips screwdriver.

1. Place the Monitor face down for access to the four (4) threaded mounting holes on the rear housing (Pic 21).

2. Attach the Mounting Adapter to the Monitor using four (4) M4 x 10mm PHMS (Pic 22).

3. Insert two (2) M4 x 10mm PHMS in the top two (2) threaded holes of the Mounting Adapter (Pic 23). Leave _'' [6 mm] of thread exposed to allow the screws to fit into the slots on the VESA Mounting Plate.

4. Guide the two (2) top screws into the mounting slots on the VESA Mounting Plate (Pic 24). Do not fully tighten these mounting screws until Step 6.

5. Insert two (2) M4 x 10mm screws in the lower two (2) mounting holes (Pic 25), securing the Monitor to the VESA Mounting Plate.

6. Tighten the top two (2) mounting screws (Pic 26).

9.0 CABLE MANAGEMENT

A Cable Clip (Pic 27) is provided for managing cables along the Roll Stand Post. Place loose cables inside the Clip and slide the Clip onto the Post as shown in Pic 28.

CASTERS:
GCX Roll Stands include (2) locking casters. To activate the locking mechanism, simply push down on the locking pedal. To release the lock, simply position your foot below the pedal and lift up until the lock has been released.

MAINTENANCE: It is recommended that all the fasteners associated with the mounting system be periodically checked and tightened as necessary.

CLEANING: The Roll Stand can be cleaned with any non-abrasive solution as approved by the facility in which the product will be used.

LIDCO SENSOR INTERFACE

INTRODUCTION

The LiDCO Sensor Interface amplifies the signal produced by the LiDCO Lithium Sensor for interpretation by LiDCO Hemodynamic Monitoring Systems. It consists of a high performance analog amplifier and a precision analog to digital convertor powered by a permanent battery, and a USB interface powered by the USB connection. The 2 sections are optically isolated.
The LiDCO Hemodynamic Monitoring System will indicate the voltage of the Sensor Interface front-end permanent battery and advise when the unit should be returned to your local LiDCO representative for service and calibration.
Calibration data and conversion factors are stored in memory within the Sensor Interface. The unit should be regularly tested and re-calibrated as required by LiDCO authorised personnel.
The device is sealed and should only be opened by LiDCO qualified service personnel.

SPECIFICATION

Analog Input (A/D converter)

• Input range: -55 to -135mV


• Over voltage: Continuous ±30V max.


• Battery voltage: 6.8 to 10.1V


• Connector: LEMO EPL0S250CLN

Control Interface

• Standard: Universal Serial Bus Specification Level 1.0


• Optical Isolation: 10kV


• Connector: USB Series B Receptacle

General

• Dimensions: 148 x 72 x 42mm


• Weight: 180g


• Operating temperature: 0 to 45°C


• Storage temperature: -20 to +65°C


• Compliance: IEC 60601-1

Roll stand mounting

1. Fit Button Feet and 12mm Washers to each of the threaded bushes using M3 x 12mm pan- or socket-head screws:

Fitting the button feet
2. The Sensor Interface can now be easily stored on, and removed from the roll stand bracket:

Panel mounting
Alternatively the Sensor Interface can be permanently mounted to a flat surface using the 4 M3 bushes:

DESKTOP STAND MOUNTING INSTRUCTIONS

INTRODUCTION

The LiDCO Flat Panel Monitor can be placed on any suitable flat surface using the desktop stand available, or permanently mounted to a roll stand, wall or ceiling using the fittings available from LiDCO and GCX Corporation.

The Flat Panel Monitor has a customized stand suitable for desktops and other horizontal locations. A unique spring inside the stand enables the monitor vertical tilt to be adjusted about 30 degrees. The stand is available from LiDCO Ltd.

Follow these procedures to set up the stand:

1. Attach the main body of the stand to the rear cover of the monitor using the four screws provided.
2.Slide the main body of the stand into the stand base. Tighten it with the two screws provided.
3. Attach the rear cover of the stand to the main body of the stand by snapping the lugs of the rear cover into the slots of the main body. When the rear cover locks into place, you will hear a click.
4. Attach the top cover of the stand to the main body of the stand by snapping the lugs of the top cover into the slots of the main body. The cover must be rotated as it is snapped into place. When the top cover locks into place, you will hear a click.

DESKTOP STAND MOUNTING

Note:
The base of the stand has two plastic caps. If you pry off the caps, you can attach the stand to your desktop using the two screw holes.

Wall Mounts and More LiDCO Mounting Solutions

GCX provides a wide range of mounting solutions for your
PulseCO™ and LiDCO Systems including Wall Mounts, Roll Stands, Ceiling
Mounts, Counter Top Mounts and Custom Mounts. For further information
please click through to the GCX website. www.gcx.com

Wall Mounts
VHM Variable Height Arm Ideal for applications requiring both vertical and lateral positioning.
M Series Articulating Arm Mounts Offers two pivot points for lateral adjustability and extension. Includes cable management under the arms and via a pass-through slide. Ideal for flat panel displays, keyboards or other small devices. Contact us for device specific part numbers.
For more informaton please visit : www.gcx.com